8/20/2023 0 Comments Magic cutter for table foilerTechniques taught include frit making (how and why), crafting pattern sheets with frit and stringer, creating patterned vitrograph stringer, cane and manipulated elements, enameled bits, making torchworked pieces for adding detail to your design as well as strategies for eliminating coldworking and devitrification. Beyond building a sea garden project the lessons taught will open your eyes to methods and techniques that can be applied to a multitude of kiln projects. As an added bonus throughout the lessons you will learn the language of artistry, including topics like color selection, contrast and composition without being overwhelmed by these basic concepts. Students will learn new techniques not covered in part one as well as learn new variations of some methods contained in part one. In this video lesson students will learn methods of layering imagery through multiple firings while learning processes for creating elements that will be used to create the imagery. Fixes For When Your Copper Foil Isn’t Centred gives you some suggestions for when your copper foiling is untidy and irregular.ġ.looks at what you can do when the copper foil isn’t centred properly leaving a wider margin on one side than the other.This video goes through two of the most common stained glass foiling mistakes.In Volume 2 Nancy takes you through all the steps to create a fantasy underwater garden. If you don’t centre the copper foil properly on the edge of the glass, you get a very thin strip of foil on one side and a a very thick strip on the other. remove the excess, as you did last time.now check the other side and do the same thing on this side, matching the foil up front and back so that when you look through the transparent glass, you don’t see copper on one side and not the other.don’t have the knife blades waggling around with nothing to support it, because you won’t get a smooth foiled line.Mine looks rusty but the blade is actually brand new! Move slowly and carefully with your finger steadying the knife blade so that your whole hand is moving around with the blade little bit by little bit trim the foil using a new or very sharp craft knife.This helps the foil stick when you trim it with the craft knife This time bias the foil deliberately the other way so that it covers the thin bit of off-centre tape stick it along the edge over the area where you’ve not foiled centrally.cut a length of copper foil at least as long as the mistake you’ve made.This is particularly annoying with transparent glass because you can see the other side of the foil. This IS a little bit fiddly to do but because the solder only sticks to the foil, the more accurate and the neater your stained glass foiling is, the better your soldering lines and your end result will be. So in my view it’s really worth spending it just a little bit of time tidying up these edges and making sure they’re as good as you can get them. How To Fix Stained Glass Foil That Isn’t Straight You’ll see that it really does make a difference, a lovely, perfect circle instead of a wonky one! 2. When your cutting has an uneven edge the stained glass foil goes on off kilter. This is how to rescue an angular misshapen corner and make it smooth and rounded.įinally, pick that tiny bit of excess away.each time you make a cut, make sure that your finger is resting on the work surface for safety.you can also move the glass rather than the blade for these tiny adjustments.move your fingers around a tiny little bit at a time.to fix it, use the exact same principle as with the circle above but because it’s a much tighter curve, make smaller increments with the craft knife.In this case it’s making the foil angular when what you want is a nice, smooth little curve. You can use the same technique in any situation with stained glass foiling when you when you’re not happy with the line that you have. Remember, the neatness of your foil equates to the neatness of your solder line. ![]() It’s best to touch and tidy up any of those annoying little corners or edges that just don’t look quite right.ĭon’t be one of those people who looks at your finished piece and feels a bit disappointed. ![]() You know you’ll regret it if you don’t ? Take that extra minute to trim your foil.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |